##issue.coverImage.altText##

Vol. 10 No. 1 (2019)

Published May 1, 2019 Pages: 1-88
Download Full Issue (PDF)

Articles in This Issue

Articles
Experimental study on thermal performance of counter flow wet cooling tower and effect of fins angle
PDF Full Text
Abstract

The aim of this paper is to in investigate the performance characteristics of counter flow wet cooling towers experimentally by varying air and water temperatures, fins angle, rate of air flow, rate of water flow as well as the evaporation heat transfer, along the height of the tower. The analysis of the theoretical results revealed before that the thermal performance of the cooling tower is sensitive to the degree of saturation of inlet air. Hence, the cooling capacity of the cooling tower increases with decreasing inlet air temperature whereas the overall water temperature fall is curtailed with increasing water to air mass ratio. From the experimental study the efficiency of the cooling tower and cooling tower characteristics are higher in case of low mass flow ratio due to higher contact area of water to air. Because of better contact area between airs to water the drop in performance of the cooling tower is less. The effect of fins angle on the thermal performance of counter flow wet cooling tower was predicted. The experimental study showed that the cooling range, cooling coefficient, , heat load , change in air relative humidity and cooling tower effectiveness increased with increasing fins angles and optimum fins angle obtained from this experimental work was 70 degree, at this angle all cooling tower performance has been calculated were better. While the approach increased with decreasing fins angles, the minimum approach was obtained for 70 degree fins angles and the maximum approach was obtained for 30 degree fins angles.

Articles
Experimental Investigation on the Efficacy of Polyethylene Aggregate on Impact Resistance of Concrete Slab
PDF Full Text
Abstract

The impact resistances of concrete slabs have a different volume fraction replacement of waste plastic aggregate has been examined in this study as a fine aggregate as: 0% (reference), 10%, 20% and 30%. These tests include the splitting tensile, density, compressive strength. Also, the (ultrasonic pulse velocity tests) was carried out. Repeated falling mass was used in order to carry out the low-velocity impact test in which a 1300 gm steel ball was utilized. From a height of 2400mm, the ball falls freely on concrete panels of (500×500×50 mm) with a network of waste plastic aggregate. As per the results, a prominent development was seen in the mechanical properties for mixes involving polyethylene aggregate up to 20% as compared to the reference mix. A significant development was seen in low-velocity impact resistance of all mixes involving waste plastic fine aggregate as compared to reference mix. As per the results, the greater impact resistance at failure is offered by the mix with (20%) waste plastic aggregate by volume of sand than others. The reference mix increased by (712.5%).

Articles
Increasing ultimate strength of reinforced concrete slab by using Reactive Powder Concrete and study the effect of high temperature on them
PDF Full Text
Abstract

The main purpose of this search is to study the punching shear behavior of fourteen specimens of Reactive Powder Concrete (RPC) two-way flat plate slabs, half of these slabs have been exposed to a high temperature up to 400 C° by using an electric oven. All slabs have dimensions of (400x400x60) mm, with steel reinforcement mesh of (Ø6mm) diameter. Laboratory tests show that there is an increase in the value of First Crack Loading (FCL) and Ultimate Load (UL) by (208, and 216.67) % and a decrease in deflection by (56.85) % due using slab with complete reactive powder relative to a slap made of normal concrete. The use of the (RPC)mixture in layers in slabs gave results close to the slab which consists of full (RPC) this gives the benefit of more than the use of a slab that contains full reactive powder concrete in terms of cost, the increase was in FCL and UL by (130.8, 169.23, 102.7 and 135.135) % and a decrease in the value of deflection by (37.17, 47.64) %. The use of a partial reactive powder mixture also showed good results, and by increasing the dimensions of the RPC area, the results were better. the increase in FCL and UL by (54, 116, and 185) % and (53, 116.67, and 166.67) % and a decrease in value of deflection by (36.12, 42.4, and 50.26) % from reference slab. When slabs are subjected to high temperatures, there may be a decrease in the value of the FCL and UL and an increase in the value of deflection when compared to models not exposed to high temperature. But when compared to the reference slab with the same circumstance showed an increase in the value of the FCL and the rate ranged between (50- 200) % and the UL was the ratio ranged between (51.35-208.1) % and a decrease in the value of the deflection where the ratio ranged (21-46) %

Articles
Study of Multi-Cracked Cantilever Composite Beams Subjected to External Moving Load
PDF Full Text
Abstract

The behaviour of multiple cracked cantilever composite beams is studied when subjected to moving periodic force. In this investigation a new model of multiple cracked composite beams under periodic moving load is solved. Three cracks are considered at different position of the beam for numerical solution. The results from experimental work compared to numerical solution. The multiple cracks are identified easily from the deflection graphs at different force speed. Influences of crack depth at different load speed are investigated

Articles
Assessment the Shear Behavior of Sustainable Thick Hollow Core Slab Using Experimental and Nonlinear Finite Element Modelling
PDF Full Text
Abstract

This investigation provides experimental results and nonlinear analysis by using finite element model of thick hollow core slab made from recycled lightweight material. Four hollow core slabs specimens were cast and tested in this investigation with dimensions (1200mm length, 450mm width and 250mm thickness). The crushed clay brick was used as a coarse aggregate instead of gravel. The iron powder waste and silica fume were used in order to increase the compressive strength of concrete. The techniques reduction hollow length and use shear reinforcement were used to improve shear strength and avoid shear failure. The specimens were tested by applying two-line load up to failure. The experimental results were showed these techniques were resisted the shear failure significantly and works to change failure mode from shear to flexural failure. Finite element computer software program (ANSYS) was used to analysis hollow core slabs specimens and compare the experimental results with the theoretical results. Good agreement have been obtained between experimental and numerical results.

Articles
Optimization of Casting Conditions for Semi-Solid A356 Aluminum Alloy
PDF Full Text
Abstract

RSM and DOEs approach were used to optimize parameters for hypoeutectic A356 Alloy. Statistical analysis of variance (ANOVA) was adopted to identify the effects of process parameters on the performance characteristics in the inclined plate casting process of semisolid A356 alloy which are developed using the Response surface methodology (RSM) to explain the influences of two processing parameters (tilting angle and cooling length) on the performance characteristics of the Mean Particle Size (MPS) of α-Al solid phase and to obtain optimal level of the process parameters. The residuals for the particle size were found to be of significant effect on the response and the predicted regression model has extracted all available information from the experimental data. By applying regression analysis, a mathematical predictive model of the particle size was developed as a function of the inclined plate casting process parameters. In this study, the DOEs results indicated that the optimum setting was approx. (44) degree tilt angle and (42) cm cooling length with particle size (30.5) μm

Articles
Compression and Wear Properties of Biocompatible Commercially Pure Titanium and (Titanium-Silicon) Alloys
PDF Full Text
Abstract

The porous Titanium is characterized by high permeability which can assure the ingrowth of bone tissues, and consequently results in a good bonding between the metallic implant and the bone. In this work, Silicon element was added to the Commercially Pure Titanium at different weight percent of (2, 4, 6, 8 and 10) to investigate its effect on the porosity percentage, mechanical properties of the resulted samples. XRD analysis stated that at (Si) content lower than (2 wt%) the alloy is single phase (α- Ti alloy), as the Silicon content increased, in addition to (αphase), (Ti5Si3) intermetallic compound developed in the alloy. Porosity measurement results showed that the porosity percentage increases with the increase in Silicon content. Wear results stated that the wear rate increases with the increase in silicon content due to the increase in porosity percentage while the hardness results stated that there is no significant effect for Ti5Si3 intermetallic compound on improving the hardness of the samples. This is attributed to its low percent and the major effect of porosity on hardness which declined the effect of Ti5Si3 by reducing the hardness of the alloy compared with the master sample. The obtained results of the (yield strength, ultimate compressive strength and Young’s modulus) were within the values that match bone’s properties. This means these materials are suitable for biomedical application

Articles
Euphrates River Water Quality Studies in Iraq: Critical Review
PDF Full Text
Abstract

The published studies about the water quality of Euphrates River in Iraq till now have been reviewed critically. The revision of the published researches depend upon several bases including the period of samples collection, the number of sampling stations, water samples collection method, the analytical techniques employed to measure and analyze the results. This critical study concluded that the need to follow a specific protocol in selection sampling sites, how the samples are collected, how samples are analyzed, and pay attention to quality assurance and quality control during sample collection, preservation and analytical procedures.

Articles
Effect of Pulse Repetition Rate on Micro Hardness on the Surface and Cross Section of Gray Cast Iron by using ND-YAG Laser
PDF Full Text
Abstract

This work, studied the effect of pulse repetition rate on the micro hardness for each of the surface and cross section by using pulsed ND-YAG laser with laser parameters (Energy = 4.12J).The distance off between the output nozzle and the minimum spot size on the surface of sample was (12mm),and pulse duration was (1.8ms).The results showed that the micro hardness increased after laser treatment ,but the micro hardness decreased with increase pulse repetition rate for both the surface and cross section of the pulses. The micro hardness increased as moving away from the molten zone towards the end of the pulses at the heat affected zone due to increase in cooling rate.

Articles
Fuzzy Reliability-Vulnerability for Evaluation of Water Supply System Performance
PDF Full Text
Abstract

The reliability of water supply system is a critical factor in the development and the ongoing capability to succeed in life and people's health. Determining of its, with high certainty, for performance of water supply system is developed to ensure the sustainability of system. Reliability (Re) plays a great role in evaluation of system sustainability. The probability approaches have been used to evaluate the reliability problems of systems. The probability approach is failed to address the problems of reliability evaluation that comes by subjectivity, human inputs and lack of history data. This research proposed two models; I) traditional model: fuzzy reliability measure suggested by Duckstein and Shresthaand then developed by El-Baroudy; and II) developed model: fuzzy reliability-vulnerability model. The two models implemented and evaluation of water supply system by using two hypothetical systems (G and H). System (G) consists of a single pump and System (H) consists of a two parallel pumps. Triangular and trapezoidal membership functions (MFs) are used to investigate of the reliability measure to the form of the membership function. The results agree with expectations that the reliability of parallel component system {ReH (0.53)} is higher than the reliability of single component system {ReG (0.47)}. Moreover, the result by using fuzzy set reduces the effect of subjectively in process of decision-making (DM). The fuzzy reliability vulnerability is able to handle different fuzzy representations and different operation environment of system

Articles
Investigation of Milling Parameters Effect on Material Removal Rate Using Taguchi and Artificial Neural Network Techniques
PDF Full Text
Abstract

The Artificial Neural Network (ANN) and numerical methods are used widely for modeling andpredict the performance of manufacturing technologies. In this paper, the influence of millingparameters (spindle speed (rpm), feed rate (mm/min) and tool diameter (mm)) on material removalrate were studied based on Taguchi design of experiments method using (L16) orthogonalarray with 3 factor and 4 levels and Neural Network technique with two hidden layers and neurons.The experimental data were tested with analysis of variance and artificial neural networkmodel has been proposed to predict the responses. Analysis of variance result shows that tooldiameters were the most significant factors that effect on material removal rate. The predictedresults show a good agreement between experimental and predicted values with mean squarederror equal to (0.000001), (0.00003025), (0.002601) and (0.006889) respectively, which produceflexibility to the manufacturing industries to select the best setting based on applications.