The reducing of heat gain through the outer walls of the buildings in summer will contribute in reducing the air conditioning costs. This is one of the best features of design requirements nowadays. To achieve this, the phase change materials (PCM) can be used as an embedded material in the walls to reduce heat transfer. The paraffin wax is one of the common materials used as a PCM in the building walls. The paraffin wax is used in this study with (20%) volume percentage in the external layer of the treated wall. In the present work, the treated wall (with embedded wax in the wall) and non-treated walls have been experimentally investigated. Two Iraqi wall models were employed to run the experiments, whereby these models were exposed to an external heat source using (1000 W) projector for each model. The temperatures were recorded at different locations in the walls during the charging and discharging periods. The results showed that the temperature of the internal surface for the treated wall was lower than that of the non-treated wall at the end of the discharging period (6 hr) where the temperature difference between the treated and non-treated walls was reached (1.6℃).
Enhancing the hydrothermal performance of plate-fin microchannels heat sink (PFMCHS) promises smaller size and lighter weight, and then improve the heat removal in consequently increase the speed of electronic devices. In this numerical study, an innovative hydrothermal design of PFMCHS is suggested by inserting elliptic pins inside microchannels in different; aspect ratio (AR) of pin, pin number ratio (ψ) in order to optimize the hydrothermal design of this kind of heat sinks. The main objectives of this study are; investigating the effect of pins on the performance of PFMCHS by investigating the best geometry in the pinned-fin MCHS and which is higher, thermal or hydraulic performance of this kind of heat sinks and what is the optimal number of pins numerically and what about the pressure drop penalty in the proposed design, little, modest or high increase. It is seen that the thermal resistance of the pinned fin MCHS is about 50% lower, and pressure drop of it is much higher than that of the (PFMCHS) under the condition of equal wind velocity. Maximum mechanical fan power reduction obtained is about 57% for the pinned fin MCHS with ψ = 1 and Dh = 1 ×10-3 m compared to the corresponding original channel heat sink. To show the overall performance of the two parameters; aspect ratio (AR), pin number ratio (ψ), the overall JF factor is estimated and the concrete findings shows that the best hydrothermal performance is obtained at the greater aspect ratio which is around overall JF = 1.2. In addition, the trend of overall JF is going down with the pin number ratio, starting from 1.2 to 1.15. And the concrete findings show that pinned fin MCHS provides thermal performance of 1.42 times greater than the smooth one under the corresponding conditions when one pin is used in each channel
An experimental study is carried out to compare the thermal performance of a sintered powder metal wick heat pipe. Pure water and absolute ethanol are used as two different working fluids. The pipe is made of copper with 300 mm length, 14 mm diameter, and 1.0 mm wall thickness. The wick is made of copper powder. All the experiments are accomplished and the heat pipe is at the horizontal position (è=0o). The heat flux changed within the range (2.8 -13.13) kW/m2, while all other conditions remained constant. The results show that the thermal performance of the heat pipe is better when water is the working fluid, where the operating temperature and the thermal resistance of the heat pipe are lower when the water is the working fluid.
This paper contributes to the field of improving the performance of heat exchangers using metal foam (MF) full-filled and partially/periodically-filled within the gap between the two pipes. The effect of configuration and arrangement of copper MF (15PPI and porosity of 0.95) installed on the outer surface of the inner pipe of a counter-flow double-pipe heat exchanger on the thermal and hydraulic performance was studied experimentally. The test section consisted of concentric two pipes; the inner pipe which was made of copper while the outer pipe was a Polyvinyl chlo-ride. Air was used as a working fluid in both hot and cold sides. A wide cold air flow rate range was covered from 3 to 36 m3/h which corresponds to Reynolds number (Re) range from 2811 to 31,335. The hot air flow rate was kept constant at 3m3/h. The temperature difference (ΔT) be-tween the inlet hot air and inlet cold air was adopted to be (20°C, 30°C, 40°C, and 50°C). The re-sults revealed that the higher Nusselt number (Nu) was at ΔT= 50°C and the thermal performance of the heat exchanger with the MF for all the arrangements was greater than the smooth heat exchanger. The highest and lowest friction factor was 1.033 and 0.0833 for the case 1 and 8, re-spectively, and the optimal performance evaluation criteria (PEC) was 1.62 for case 7 at Re = 2800. The Nu would be increased with a moderate increase in the friction factor by optimizing the arrangement of the MF. The two essential parameters that played an important role for in-creasing the PEC were the MF diameter and the MF arrangement along the axial length of the cold air stream.
The present paper addresses the numerical study of non-Darcy laminar forced convectionflows in a pipe partially filled with grooved metallic foam attached in the inner pipe wall,which is subjected to a constant heat flux. Computations are carried out for nine differentdimensions of grooves with different Reynolds numbers namely; (250 ≤ Re ≤ 2000) andtheir influences on the fluid flow and heat transfer are discussed. The governing and energyequations are solved using the finite volume method (FVM) with temperature-dependentwater properties. The novelty of this work is developing of a new design for the metallicfoam, which has not studied previously yet. It is observed that the two helical grooves withtwo pitches increase the Nu around 5.23% and decrease the pumping power nearly 12%. Itis also showed a reduction in the amount of material required for manufacturing the heatexchanger, which leads to a decline in the weight of the system 8.29%.