Management of water resources become one of the most important subjects in the human's life. The water sustains life on earth, therefore; more care for water management is necessary. In the last years, studies show water use will be more in the world as result of rapid increase in population, industrialization, and urbanization etc. The evaporation losses from dam's reservoirs and lagoon form very huge losses in water resources. The annual evaporation depth losses in Iraqi Western Desert is about (2.25 -3) meter, this depth store the highest percentage of the small dams. Sub-surface storage reduces evaporation losses and maintains water quality by minimizing salt concentration. In present study, three tanks are used to simulate the subsurface reservoirs to study the effectiveness of underground storage on reducing the evaporation loss. Each tank have squares cross section tanks of (80) cm length and (40) cm depth and filled up to (34) cm with different graded soil (labeled as A, B with coarse soil, and D with fine soil) to simulate the storage below the ground. While the forth tank filled with water (labeled as C) to represent the reservoir of direct evaporation for comparison study. The present study considers three parameters that can controlled the evaporation from subsurface reservoirs: (a) temperature variation, (b) water table variation, and (c) material properties such as porosity. The field study continues for four months, it was started at Jun.11, 2016 and ended at Dec. 15, 2016 in the Erbil city at north of Iraq. The results showed evaporation losses are reduced by using subsurface storage reservoir with gravel in comparison with free surface evaporation. The evaporation losses are reduced about 46 % , 39% , 64% when the water table below gravel surface range from 5 to 10 cm , while at 20 cm depth of the water table the evaporation reduction is about (85 % to 86% 95%) from A, B and D tanks with porosity 0.65 ,0.67 and o.35 for A ,B and D tanks, respectively..
minimizing the surface area of a reservoir during maximum evaporation losses period. A mathe-matical relationship linking the depth of water with the surface area of the reservoir has been formulated, and its integration can be used to estimate conservable water quantities. Reducing the water level in the reservoir to the minimum permissible level before the dry months has re-duced the evaporation losses by 65% and 51% for the two scenarios. These two scenarios have been conducted by assuming that the dry months start with the presence of the water level in the reservoir at a height of 14 and 12 m, respectively. On the other hand, evaporation losses during drought months have been decreased by 24%. By this technique, it can be possible to obtain wide areas suitable for agriculture, contributing to the economic and social development of the region. Also, Depth index(DI) suggested in this study and defined as the ratio of volume of the water in the reservoir to corresponding surface area, to compare the location of the best dam among the 13 proposed dams in Wadi Houran by reducing evaporation losses. The results of this index showed the best location was at DI=10.901 in DM 7, and the worst is at DI=2.425 in DM 8.
Switched reluctance motor (SRM) is an electric motor works based on the reluctance torque produced due to the variation of the rotor pole position with respect to stator poles. This paper adopts a thermal analysis on a 4-phase, 8/6 pole, 550W, SRM. Lumped parameters thermal network method(LPTN) is used in this analysis based on a combination of RMXprt/Motor-CAD software, in two- dimensional(2D), steady-state, with different cooling methods, and with different loading conditions. Motor losses like core losses, copper losses, and mechanical losses are regarded as the heat sources in SRM which are calculated by RMXprt software. The thermal analysis achieved by Motor-CAD includes displaying the temperature distribution on different motor parts like stator winding, stator poles, stator yoke, rotor poles, rotor yoke, shaft, covers, and housing. The analysis results showed the increasing temperature distribution on different motor parts with increasing motor loading conditions. Also, this temperature distribution is recorded using three different cooling methods. The comprehensive thermal analysis applied in this work will assist the motor designer in choosing a better motor thermal design without needing to produce and test costly prototype motors.
ORE addresses various kinds of losses associated with manufacturing system which can be targeted for initiating improvements. Evaluating ORE will is helpful to the decision maker(s) for further analysis and continually improves the performance of the resources. Overall Resource Effectiveness (ORE) encompasses seven factors are; performance, quality rate, readiness, changeover efficiency, availability of material and availability of manpower. In this research Job shop production of General Company for hydraulic industries, with focus on Damper and Tasks Factory (DTF)is tested as a case study for two of the most customer demand rear dampers (Samaned and Nissan). Data are collected and analyzed for years 2016-2017 to evaluate of ORE values. Results show that process performance factor among other seven factors have the less value causing the highest loss in ORE decrease. Where the highest ORE value is (58.6%) for Nissan and (69.3) for Samaned rare production. Also, time loss due to set up time is detected where it ranges from 3% to about 13% per month for the above mentioned two tested dampers. Results are generated employing Minitab Version 17, Quality Companion Version 3 soft wares. It is recommended to introduce SMED (Single Minute Exchange of Dies) concept that could decrease losses in set up time .Also improvements in maintenance programs are vital, and above all improving process performance values is essential by employing lean manufacturing that result in fast outcomes ,and TQM process improvement strategy for long term outcomes these two process performance strategies may enhance ORE values therefore, decrease losses, and consequently increase quality and productivity.
The term "fire safety engineering" refers to the process of applying scientific and engineering principles to the effects of fire in order to lessen the number of deaths and property damage caused by fire. This is done by determining the risks that are involved and providing the most effective method for implementing measures of prevention or protection. The paper showing experimental results of ordinary concrete columns made of "NSC" subjected to axial load and cyclic firing is presented in this study. the bearing capacity of the column decreased. all samples have been loading an eccentric load with "e = 75 mm" ,"e / h = 0.50," and the ratio Celsius (30%Pu) continuously through the burning period. The first column(C1) was the sample control with out exposure cyclic fire , and the second column was subjected to four burning cycles over the course of four days, with a duration specific of "45 minutes" for each cycle, at a temperature of "400 °C", and the third column was subjected to four burning cycles over the course of four days, with a duration longer amount of "75 minutes" for each cycle, at a temperature of "400 °C, ", the four column was subjected to four burning cycles over the course of an of four days, with a duration specific of "45 minutes" for each cycle, at a temperature of "600 °C " , the bearing capacity of the column decreased. that to be amount losses (C2,C3 and C4) comparison to (C1) equile ( 27.20 , 29.12, and 36.40)% respectively. the fracture load of the experimental columns varied by decreasing with these variables. Additionally, the depth and spread of the cracks increased with the increase in burning duration and target temperature.
Flow of crude oil in pipelines suffers from a problem of fluid flow pressure drop and high energy consumption for fluid pumping. Flow can be enhanced using either viscosity reduction or drag reduction techniques. Drag reduction (DR) is considered as a most effective and most applicable method. The technique contributes in reducing the frictional energy losses during the flow by addition of little amounts from drag reducing agents. The present work focuses on preparation and application of a new natural and low cost material derived from palm fiber (PF) that has been tested as a drag reducing agent (DRA) for crude oil flow enhancement. This objective has been achieved through designing and constructing of an experimental rig consisting of: a crude oil pipe, oil pump, pressure sensors, solenoid valve and programmable logic control. The additive material (PF) is prepared with different diameters (75µm, 125µm, 140µm) and tested with different concentrations as: 100, 200, 300, 400, and 500 mg/L for reducing the drag inside the oil pipe. The experimental results showed that the fiber with 125µm diameter and 100ppm is the best where the percentage of drag reduction reached 43%. Furthermore, the results of this work proved that PF is an efficient and low cost DRA that can be applied successfully in crude oil pipelines as well as its contribution in the waste management.
A gradual change in the state and properties of the oil transformer due to aging, which generally leads to break down. Aging of the mineral oil cause permanent harmful change of the ability insulation system. Aging of the mineral oil and water content of paper insulation are simulated at the laboratory by putting the samples of the oil and pieces of insulation paper in a rig (transformer manufactured) and exposed to different temperatures (20Co, 40Co, 60Co, 80Co) for specific durations of time to analysis and improve the performance of the transformer. In this research, the electrical and physical characteristics for the mineral oil and paper insulation have been studied and then repeated by the addition of different concentration of Nanoparticales (ZnO) (0.01, 0.03, 0.05, 0.07)gm/ml then compared with the electrical properties of the pure mineral oil and paper insulation without (ZnO) nanoparticales
The studying of the distribution of wetting patterns in soils having a stratified profile is of great importance due to the presence of this type of profile in abundance in agricultural lands, including greenhouses. Therefore, there was a need to develop a numerical program that predicts the dimensions of the wet area of the subsurface drip irrigation system under different operating conditions for purpose design and manage these systems properly to avoid water losses resulting from evaporation or deep penetration. The present study aims to develop a two-dimension model simulates the wetting pattern in stratified soils using (HYDRUS-2D) software and study the effect of soil hydraulic properties and different operating conditions on the progress of the wetness pattern and the interference pattern between two wetting fronts. Laboratory experiments were carried out for the system of subsurface drip irrigation in stratified soils that consisted of three layers (silty clay loam soil, loamy sand soil, and sand soil) arranged from bottom to up. Three different emitter flow rates 0.5, 1, and 2 l/h were tested, as well as three different initial moisture contents for each soil layer were considered. The interference pattern between two wetting fronts of two emitters with different spacing between emitters 30, 40, and 50 cm was studied. A numerical model was developed to guess the horizontal and vertical dimensions of the wetting zone for the single emitter and the pattern of interference between the two wetting fronts of two emitters. The predicted values obtained from the numerical model were compared with those obtained from laboratory experiments. Statistical analysis of the obtained data showed that the developed numerical model has a good ability to guess the dimensions of the wet pattern of the single and the two emitters and there were good agreements between the predicted and the experiments results and minimum values of RMSE ranged between 0. 5 and 3.6 were achieved.