This research paper is an attempt to reuse plastic waste fibre resulting from plastic sections industry as an additive to concrete matrix. The relationship between fibre volume fraction and mechanical properties of concrete and re-inforced concrete tiles was investigated. Three volume fractions of fibre ( 0.5 % , 1 % and 1.5 % - by volume of concrete ) were used through the experi-mental program. Tests’ results proved a slight decrease in concrete compres-sive strength as plastic fibre was added compared with the reference mix. Flexural behaviour of concrete tiles was enhanced as adding fibres. Adding fibre to Concrete results in a negligible reduction in concrete density. Fibre with high volume fractions improved Splitting tensile strength compared to the reference mix.
The convergence of cloud and edge computing in smart manufacturing offers significant potential for improving efficiency in Industry 4.0. However, task scheduling in this context remains a complex, multi-objective challenge. This study introduces a novel Cloud-Edge Smart Manufacturing Architecture (CESMA), leveraging a hybrid approach that integrates NSGA-II and the Improved Monarch Butterfly Optimization (IMBO) algorithms. The combination utilizes NSGA-II's global search and non-dominated solution capabilities with IMBO's fine-tuning and local optimization strengths to enhance task scheduling performance. Where CESMA combines the scalability and analytics power of cloud computing with edge-based real-time decision-making to address the dynamic demands of smart manufacturing. Through extensive simulations and experiments, the feasibility and effectiveness of CESMA are validated, showing improved task scheduling quality, resource utilization, and adaptability to changing conditions. This research establishes a robust platform for managing the complexities of task scheduling in cloud-edge environments, advancing intelligent manufacturing processes, and contributing to the integration of evolutionary algorithms for real-time industrial decision-making
Since concrete is one of the most popularly utilized building mixtures in construction, a high demand of natural resources is significantly emerged. Therefore, a skyrocketed attention has been paid to create new opportunities for the use of recycle materials to develop a new construc-tion substance with more satisfactory properties. The use of waste products in concrete is not only economical, but it helps in solid waste management as well. Among various properties of concrete, thermal conductivity is a crucial factor that plays an important role in in building insu-lation by evaluating a material's capacity to transfer heat. This paper aims to review the potential application of waste materials in concrete as additive ingredients and investigate the effect of this waste material on thermal conductivity of concrete. The review of literature revealed that the application of most of the waste materials exhibited an obvious potential as thermal insulator. However, further investigated work is needed to highlight the advantages of utilizing waste mate-rials in concrete containing various type of waste materials
The White Cement Kiln Dust (WCKD) is a byproduct material, formed in cement factory during the operation of cement production. In highway construction, the WCKD can be used in different ways such as stabilizing the subgrade of highway embankment and as mineral filler in Hot Mix Asphalt (HMA); the latter usage will give clean and healthy environment in addition to more economy. In Iraq, there are two common types of fillers, Portland cement and lime stone powder. In this research, WCKD taken from Fallujah cement plant used as mineral filler in addition to two common types. Various percentages , such as 100%WCKD, 50%WCKD + 50%Cement(C) ,100%C , 50%WCKD+50%Limestone (L), and 100% L, were used to prepare asphaltic concrete mixes. In general, five tests were used to evaluate the performance of these mixes. Standard Marshall Test procedure was applied under three different conditions, two of them at two temperatures at 60 OC and 70 OC and in the third one it was used to test samples immersed in water, at room temperature(24 OC), for four days. Indirect Tensile Strength Test (ITST) was used to evaluate conditioning and un-conditioning samples. All test results, when compared with controlled asphalt concrete sample (Sample contained 100% limestone as filler), were acceptable and within the AASHTO and Iraqi Standard Specifications of Roads & Bridges 2003. Stability values, at standard condition test, of samples containing 100% WCKD, 50%WCKD+50%C, and 50%WCKD+50%L are 11.9kN, 13.2kN, and 14.0kN respectively, while for controlled sample was 9.0kN. The Marshall stiffness values showed similar trends, for samples having 100% WCKD, 50%WCKD+50%C, and 50%WCKD+50%L giving 3.22kN/mm, 3.38kN/mm, 3.5kN/mm respectively but for controlled sample was 2.43 kN/mm. Same trends of results gained in ITST .The results showed the beneficial using of WCKD as filler that will conserve the environment and encourage the HMA producers to use this inexpensive material in their works.
In this paper, the hydraulic-thermal performance of a double-pipe heat exchanger equipped with 45°-helical ribs is numerically studied. The ribbed double-pipe heat exchanger is modelled using three heights (H = 0, 2.5, 3.75, 5 mm) of 45°-helical ribs. Two numbers (4-ribs and 8-ribs) of 45°-helical ribs are attached on the outer surface of the inner pipe of the counter-flow double-pipe heat exchanger and compared with a smooth double-pipe heat exchanger. Three-Dimensional computational fluid dynamics (CFD) model for a laminar forced annular flow is performed in order to study the characteristics of pressure drop and convective heat transfer. In addition, the influence of rib geometries and hydraulic flow behaviour on the thermal performance is system-atically considered in the evaluations. The annular cold flow is investigated with the range of Reynolds numbers from 100 to 1000, with three heights of ribs at the same width (W = 2 mm) and inclined angles of (θ = 45°).The results illustrate that the average Nusselt number and pressure drop increase with an in-creasing number of ribs, the height of ribs and Reynold number, while the friction factor decreas-es with increasing Reynolds numbers. The percentage of averaged Nusselt number enhancement for three rib heights (H = 2.5, 3.75 and 5 mm) at 4-ribs is (34%, 65% and 71%), respectively, While for 8-ribs the enhancement percentage is (48%, 87% and 133%) as compared with the smooth double-pipe heat exchanger at Re = 100. The best performance evaluation criteria of (PEC) at (8-ribs, and H = 5 mm) is 2.8 at Re = 750. The attached 45-helical ribs in the annulus path can generate kind of secondary flows, which enhance the fluid mixing operation between the hot surface of the annular gap and the cold fluid in the mid of the annulus, which lead to a high-temperature distribution. Increasing the height of 45°-helical ribs lead to an increase in the sur-face area subjecting to convective heat transfer.
This research presents a mathematical model of feed-interval scallop height, where in a machined surface there are two types of scallop height, the pick(path)-interval scallop and the feed-interval scallop. The pick-interval scallop is generated by the finite pick offset between the successive cutting paths, while the feed-interval scallop is generated by the finite increment between the successive tooth feeds. New model that describes and predicts the geometric generating mechanisms of the feed-interval scallop height have been derived using torus cutter which is commonly used in multi-axis milling machine. The machining parameters (effective tool cutter radius, feed per tooth and the magnitude of tool axis inclination angles) have been considered in theoretical and experimental work to study the effect of these parameters on this type of scallop height. From theoretical and experimental work it was found that at high-speed machining, the feed-interval scallop is more important to the surface roughness than the path-interval scallop, and the feed-interval scallop is very sensitive to the tool-axis inclination angle. The feed-interval scallop height decreased sharply and quickly within a few degrees of the tool-axis inclination to the normal workpiece surface. In general, an inclination angle equal to is good enough for all tool diameters used in the present work, namely (6,8,10 12 mm).
In this study an attempt is made to derive governing equations satisfying equilibrium and compatibility, for multi-layer composite simply supported beam under blast loading , for linear material and shear connector behavior in which the slip (horizontal displacement) and uplift force (vertical displacement) are taken into consideration. The analysis is based on an approach presented by Roberts, which takes into consideration horizontal and vertical displacements in interfaces. The model consists of a simply supported beam with three layers having a cross-sectional area ,different dimensions and material properties. The analysis led to a set of six differential equations containing derivatives of the fourth and third order. The blast loading was considered as a function of time. Explosions have different effects including blast, penetrations and fragmentation. The blast is the main effect which hits the structure in short duration. Multi –layer composite construction is the best type of constructions to resist the blast loading ; according to this , multi-layer composite construction is used for air-craft and marine industries. Analysis of composite beam under blast load , taking in consideration vertical and horizontal displacements, leads to six differential equations , the load is taken as a function of time.
Nowadays, renewable energy sources are becoming further utilized to produce electricity. Fuel cell (FC) is one of the encouraging renewable and sustainable power resources as a result of its high power density and extremely low release. This paper presents suggestion and implementation of FC power system. So as to design a greatly efficient FC power system, proper DC - DC and DC - AC converters are needed. Among the different types of DC - DC converters, Interleaved Boost Converter (IBC) has been proposed as appropriate interface between FC and the next stage to transform the produced power energy (low voltage high current input into a high voltage low current output of the FC). 11-level Neutral Point Clamped (NPC) Multilevel Converter (MLC) is proposed for converting the DC output of the IBC to AC voltage to feed the load. MLC is chosen because it has many attractive features like high voltage capability, smaller or even no output filter, low voltage stress on load. Simulation of the proposed FC power system has been performed using MATLAB/SIMULINK..
Photovoltaic cells are one of the renewable energy sources that have been employed to produce electrical energy from solar radiation falling on them, but not all incident radiate will produce electrical energy, part of those radiate cause the panel temperature to rise, reducing its efficiency and its operational life, unless an attempt is made to employ one of the traditional cooling methods or innovating other methods to cooling it to reduce this effect, which it represented in the active and passive cooling method. In fact, it is difficult to compare the active method with the passive method, as each method has its Advantages and disadvantages that may suit one region without another. But in general, there are basic factors through which at least a comparison between the two methods can be made. Relatively the passive method is less expensive, in addition to no need for additional parts such as pumps and controllers, there is no energy consumption because it does not require power. But it is less effective and efficient than the active method, while the active method has the ability to disperse the heat higher than the passive method. However, it necessitates the use of electricity and is frequently costlier than the passive strategy. In this review, the most common active and passive cases were reviewed, and the pros and cons of each case are summarized in discussion due to the difficulty to list them. The review recommends that future studies should focus on active water cooling and heat-sink, both of which are viable cooling strategies.
This research focuses on studying the speed flow density relationships which are considered the fundamental traffic flow relationships. The objective of the present study is to predict statistical models represent these relationships depending on a field survey data collected from Al-Thirthar road in Falluja city.Data were collected by using video-recording technique. The required data were abstracted, analyzed, grouped, and processed using computer programs developed for this purpose. Standard statistical analysis techniques were used to examine and analyze the observed data.FWASIM simulation traffic software program was used to verify the predicted traffic stream models, while the obtained results were presented in this research. To test the validity and reliability of the model, the output results of the predicated model were compared with the output data obtained from FWASIM model using similar input data and segment geometry. The comparison leads to consider that the developed regression model may be used to evaluate the performance of urban streets in Falluja city.
Our project was divided into two distinct sections, circuit transmitting and receiving ultrasoundWave Based on Laser Light. A Wien Bridge and a Triangle Wave Oscillators used to obtain a sineand a triangular wave, respectively. A comparator circuit which produces Pulse Width Modulation(PWM) that has the same frequency for triangle wave. The PWM was used to drive laserdiode that produced laser light through by MOSFET transistor and received this light by receivingcircuit which consists of a photodiode with resistor as a voltage divider, amplifier circuit to amplifythe signal and filter to get any desired frequency. The main objective of this project primarilywas to realize a transmission-reception system to transfer ultrasound Frequency via Laser withouta guiding medium, using modulation with little quality loss.
Advanced prosthetics are a crucial aspect of rehabilitation technology and are receiving increased attention globally. Approximately 2 million people require prosthetic limbs, presenting opportunities for enhancing their quality of life. State-of-the-art technologies such as realistic arms and myoelectric prostheses are gaining popularity. Progress in sensor technology, artificial intelligence, and materials has driven the field forward. Various types of controllers, including direct, pattern recognition, and proportional-derivative, have been developed. Integration of material science, computer science, artificial intelligence, and neurology has facilitated controller advancements. Techniques like targeted muscle reinnervation and Osseo integrated prostheses offer improved surgical options. Gesture recognition technologies and intelligent sensors are enhancing hand control. Future advancements will involve machine learning, artificial intelligence, and sensing techniques, while ethical concerns must be addressed. Advanced myoelectric prostheses, also known as myocontrolled or lower-limb micromod investigative prostheses, have a patient acceptance rate of 75% to 80%. However, while these methods offer advantages, there are also drawbacks. Integrating different types of controllers for these smart prostheses and enhancing the overall device's strength and robustness will have a significant impact. This discussion focuses on various types of smart prosthetic controllers, dividing muscle activity into extracellular myoelectric potential and EEG signals
This research presented a strategy for designing a particular set of surfaces, obtained by the technique of cross-sectional design. The surfaces considered were formed by sliding a Bezier curve (profile curve), and also this research describes an automatic procedure for selective identification of sampling points in reverse engineering applications using Coordinate Measurement Machine. In addition, Matlab program have been used in the present work so as to plot the curve sections of the surfaces using transformation matrices. UGS program have been also used to connect the sections that designed in Matlab program to get the final shape of the proposed surface. It can be concluded that the whole steps task which built in the present research can be programmed in a single block of the part program that’s from it can be create any curve or surface at minimum designing time.
This paper contributes to the field of improving the performance of heat exchangers using metal foam (MF) full-filled and partially/periodically-filled within the gap between the two pipes. The effect of configuration and arrangement of copper MF (15PPI and porosity of 0.95) installed on the outer surface of the inner pipe of a counter-flow double-pipe heat exchanger on the thermal and hydraulic performance was studied experimentally. The test section consisted of concentric two pipes; the inner pipe which was made of copper while the outer pipe was a Polyvinyl chlo-ride. Air was used as a working fluid in both hot and cold sides. A wide cold air flow rate range was covered from 3 to 36 m3/h which corresponds to Reynolds number (Re) range from 2811 to 31,335. The hot air flow rate was kept constant at 3m3/h. The temperature difference (ΔT) be-tween the inlet hot air and inlet cold air was adopted to be (20°C, 30°C, 40°C, and 50°C). The re-sults revealed that the higher Nusselt number (Nu) was at ΔT= 50°C and the thermal performance of the heat exchanger with the MF for all the arrangements was greater than the smooth heat exchanger. The highest and lowest friction factor was 1.033 and 0.0833 for the case 1 and 8, re-spectively, and the optimal performance evaluation criteria (PEC) was 1.62 for case 7 at Re = 2800. The Nu would be increased with a moderate increase in the friction factor by optimizing the arrangement of the MF. The two essential parameters that played an important role for in-creasing the PEC were the MF diameter and the MF arrangement along the axial length of the cold air stream.
Free vibration analysis of a cracked cantilever beam with two types of additional substructure attachment is investigated using ANSYS program. The cantilever beam is used as a master structure with single substructure attachment in various locations (as 1-DOF mass attachment and 1-DOF mass-spring attachment) with influence of crack in different location and depths. The results for the changes of the natural frequencies of a cracked beam are compared with the results produced by Vahit et al [1]. So the same geometrical properties have been studied. In additional work a cracked beam carrying two types of substructure attachment are compared with the results of the beam without a crack and with multi crack depth. In all calculations the beam has a uniform cross-section and the crack was modeled by reduction in the modulus of the beam. The reducing effects of the cracked beam on the natural frequencies had been more apparent with the substructure attached to the beam in different situations. The effect of mass-spring substructure is larger than the effect of the attachment when modeled as mass substructure for the same mass, with 17% for the first natural frequency and 2% for the second and third natural frequencies. The results can be used to identify cracks in simple beam structure; cracks have a clearer decreasing impact on the natural frequencies.
Enhancing the hydrothermal performance of plate-fin microchannels heat sink (PFMCHS) promises smaller size and lighter weight, and then improve the heat removal in consequently increase the speed of electronic devices. In this numerical study, an innovative hydrothermal design of PFMCHS is suggested by inserting elliptic pins inside microchannels in different; aspect ratio (AR) of pin, pin number ratio (ψ) in order to optimize the hydrothermal design of this kind of heat sinks. The main objectives of this study are; investigating the effect of pins on the performance of PFMCHS by investigating the best geometry in the pinned-fin MCHS and which is higher, thermal or hydraulic performance of this kind of heat sinks and what is the optimal number of pins numerically and what about the pressure drop penalty in the proposed design, little, modest or high increase. It is seen that the thermal resistance of the pinned fin MCHS is about 50% lower, and pressure drop of it is much higher than that of the (PFMCHS) under the condition of equal wind velocity. Maximum mechanical fan power reduction obtained is about 57% for the pinned fin MCHS with ψ = 1 and Dh = 1 ×10-3 m compared to the corresponding original channel heat sink. To show the overall performance of the two parameters; aspect ratio (AR), pin number ratio (ψ), the overall JF factor is estimated and the concrete findings shows that the best hydrothermal performance is obtained at the greater aspect ratio which is around overall JF = 1.2. In addition, the trend of overall JF is going down with the pin number ratio, starting from 1.2 to 1.15. And the concrete findings show that pinned fin MCHS provides thermal performance of 1.42 times greater than the smooth one under the corresponding conditions when one pin is used in each channel
The construction of pavement layers on subgrade soil with good characteristics decreases the thickness of these layers, which in turn lowers the cost of building and maintaining roadways. However, it is impossible to avoid constructing pavements on unsuitable subgrade due to a number of limitations. Using conventional additives like lime and cement to improve subgrade properties results in additional costs. As a result, utilizing by-products (cement kiln dust and reclaimed asphalt pavement) in this field has benefits for the environment, economy, and technology. Large amounts of cement kiln dust (CKD), a by-product material, are produced in Portland cement factories. On the other hand, large amounts of reclaimed asphalt pavement (RAP) are accumulated as a result of the rehabilitation of old roads. This paper discusses using CKD and RAP to improve the characteristics of poor subgrade layers by conducting a series of Unconfined Compressive Strength (UCS) and California Bearing Ratio (CBR) tests on samples of natural soil and soil stabilized with different percentages of CKD and RAP with different curing times to investigate their impacts on soil properties. The curing was carried out by wrapping the stabilized samples with several layers of nylon and then placing them in plastic bags at room temperature. The compaction results illustrated that the addition of CKD increases OMC and decreases MDD, in contrast to RAP, which decreases OMC and increases MDD. The addition of CKD and RAP led to a significant and unexpected increase in the CBR values. The results show that the soaked and unsoaked CBR values improve from 3.4% and 12.1% for natural soil to 220.1% and 211%, respectively, after adding 20% CKD and curing the samples for 28 days. Also, the addition of 25% RAP to soil-20% CKD blend increased the soaked and unsoaked CBR values to 251% and 215%, respectively. All the additions resulted in a significant reduction in swelling.
Natural convection heat transfer in two-dimensional region formed by constant heat flux horizontal flat tube concentrically located in cooled horizontal cylinder studied numerically. The model solved using the FLUENT CFD package. The numerical simulations covered a range of hydraulic radius ratio (5, 7.5, and 10) at orientation angles from (0o up to 90o). The results showed that the average Nusselt number increases with hydraulic radius ratio, orientation angles and Rayleigh number. As well as enhancement ratio for Nusselt number at orientation angle 90o and hydraulic radius ratio 7.5 equal 24.87%. Both the fluid flow and heat transfer characteristics for different cases are illustrated velocity vectors and temperature contours that obtained from the CFD code. The results for the average Nusselt numbers are compared with previous works and show good agreement.
This study focuses on improving the thermal comfort in Mosques in Iraq. Omar bin Abdul Aziz Mosque in Baghdad is taken as a case study. In general, the weather in Baghdad is hot- dry climate during the summer. the study was conducted at the time of noon prayer on Friday where the maximum number of people can be obtained inside the Mosque about 500 worshipers and severe environmental conditions. Numerical methods (CFD) are used for the simulation utilizing the package of ANSYS (FLUENT V. 18). As the results depending on the number of elements, 4 millions elements are used for dividing the physical domain. Thermal comfort was assessed by finding the values of the predicted mean vote (PMV), predicted percentage of dissatisfied (PPD), and ASHRAE standard-55. The adaptive redistribution of the air conditioning device strategy at five cases is used to obtain the best thermal comfort. Moreover, changing the angle of air intake of space by changing the angle inclination of the access blade at three different angles of 0o, 7.5o and 15o degree, and studying its effect on the thermal comfort in breathing level. The four case is the best in terms of thermal comfort when the angle of intake air at 0o.when the PMV was 0.35 and PPD is 7.5, which is lower than the original state. The improving percentage of PPD is 10 % and PMV 14 %.
Diesel electrical generators are essential for providing reliable backup power during grid outages, ensuring the continuous operation of critical services such as hospitals, industries, and communication systems. These generators require instantaneous monitoring and control to optimize their performance and longevity. The Internet of Things facilitates efficient monitoring and enables remote control with a faster response time than human intervention, thereby helping to prevent potential damage or system failures. This research introduced the Internet of Things technology and its general architecture. The study first presented an abstract framework of IoT-based monitoring and controlling technology, divided into three layers: perception, network, and application. It then discussed the terminology related to electrical generators, the parameters monitored, and their operational environments. In addition, the advantages and challenges associated with integrating it with electrical generators were discussed. Finally, the research reviewed and analyzed several practical applications and case studies integrating IoT with diesel electrical generators, highlighting key challenges and proposing solutions. This work provided theoretical and practical insights into IoT-based monitoring and control systems for electrical generators.
Recently, the investigations studies of simulating flow over spillways have increased using numerical models. Due to its important structure in the dams to pass flood wave to the downstream safely. Researches finding have shown that CFD (Computational fluid dynamics) models as the numerical method are a perfect alternative for laboratory tests. Performance analysis of the CFD platforms Ansys Fluent-2D and Flow-3D are presented, focus on finding the variations between the numerical results of the two programs to simulate the flow over ogee spillway. The present study treats the turbulence using RNG k-ε of RANS approach, and also use the Volume of Fluid (VOF) algorithm to track the water-air interaction. The Fluent-2D and Flow-3D accuracy are assessed by comparing representative flows variables (velocity; free surface profiles; pressure; and the turbulent kinetic energy). The results of both codes have been also compared with experimental data. The results of the analysis show an excellent agreement between the two platforms data, which could assist in the future by using both programs to calibrate each other, rather than traditionally relying on laboratory calibration models.
Composite laminate plates, fabricated by bonding fiber–reinforced layers, were dynamically analyzed under different combinations of number of layers, type of cutout, hole dimensions, angle of lamination and type of dynamic loading . This work was achieved by the well–known engineering software (ANSYS). The toughness of composite plates was evaluated in terms of the normal stress in the direction of loading at the periphery of the cutout. The toughness was found to increase by increasing the number of layers, by setting the lamination angle at around 40o,by selecting hole dimensions to width of plate ratio of around 0.4 and by employing square cutouts or avoiding triangular cutouts. Also, composite plates were found to be more strain-rate-sensitive in ramp loading, with least number of layers and with triangular type of cutout.
In this paper, turbulent convective heat transfer in a triangular-ribbed chan-nel has been numerically investigated. SiO2-water with nanoparticles volume fraction of 4% and nanoparticles diameters of 30 nm is employed with Reyn-olds number ranging from 2000 to 8000. The governing continuity, momen-tum and energy equations in addition to low Reynolds number k-ε model have been transformed into body-fitted coordinates system and then solved using finite volume method. The effects of Reynolds number and rib heights on Nusselt number, pressure drop, thermal-hydraulic performance factor and entropy generation are presented and discussed. It is observed that the Nusselt number, pressure drop and thermal performance increase with in-creasing of Reynolds number and rib height. In addition, the highest perfor-mance factor can be obtained at Reynolds number of 6500 and rib height of 1.5 mm.
This paper deals with a numerical investigation of natural convection of heat transfer in a horizontal eccentric annulus between a square outer enclosure and a heated circular inner cylinder. The governing equations are expressed by the term of the stream function-vorticity with dimensionless temperature. The body fitted coordinate system (BFC) was used to stretch over the physical domain of the presented problem. The Poission's equation of stream function is solved by successive over relaxation (SOR) method, while time marching technique was the best choice to solve both vorticity and energy equation.The results are presented for the streamlines and isotherms as well as the average Nusselt number at different eccentricities and angular positions. Comparison with previous theoretical results shows good agreement.
This article presents a numerical study on forced convection of nanofluid flow in a two-dimensional channel with trapezoidal baffles. One baffle mounted on the top wall of channel and another mounted on the bottom wall of channel. The governing continuity, momentum and energy equations in body-fitted coordinates are iteratively solved using finite volume method and SIMPLE technique. In the current study, SiO2-water nanofluid with nanoparticles volume fraction range of 0- 0.04 and nanoparticles diameters of 30 nm is considered for Reynolds number ranging from 100 to 1000. The effect of baffles height and location, nanopar-ticles volume fraction and Reynolds number on the flow and thermal fields are investigated. It is found that the average Nusselt number as well as thermal hydraulic performance increases with increasing nanopartiles volume fraction and baffle height but accompanied by increases the pressure drop. The results also show that the best thermal- hydraulic performance is obtained at baffle height of 0.3 mm, locations of baffles at upper and lower walls of 10 and 15 mm, respectively, and nanoparticles volume fraction of 0.04 over the ranges of Reynolds number.
Satellites may provide data with various spectral and spatial resolutions. The spatial resolution of panchromatic (PAN) images is higher, but the spectral resolution of multispectral (MS) images is greater. There is Satellite sensors limitation for capturing an image with high spatial and spectral resolution, due to the hardware design of the sensors. Whereas many remote sensing, as well as GIS applications, need high spatial and spectral resolution. Image fusion merges images of different spectral and spatial resolutions based on a certain algorithm. It can be used to overcome the sensor's limitation and play an important role in the extraction of information. The standard image fusion approaches lose spatial information or distort spectral characteristics. Optimizations of fusion rules can overcome and degrade the distortions as the fusion core is the image fusion rules. In this paper, the Grey Wolf Optimizer (GWO) is used to find the optimal injection gain, as most distortions in image fusion are caused by the extraction and injection of spatial detail. Both qualitative and quantitative metrics were utilized to evaluate the quality of the merged image. The mentioned metrics that were used commonly for evaluation of image fusion results support the proposed algorithm for image fusion as the output image was qualitatively and quantitatively growth. In the future the proposed method can be updated by increasing the objective function dimensions to two or three for getting a best fused image.
Determinations of unsaturated soil parameters using experimental procedures are time consuming and difficult. In recent years, the soil–water characteristic curve (SWCC) has become an important tool in the interpretation of the engineering behavior of unsaturated soils. Difficulties associated with determining such parameters have justified the use of indirect determination. This paper presents the general nature of the SWCC for soils with different plasticity limits, index and gradation, in terms of gravimetric water content and degree of saturation versus soil matric suction from Anbar governorate. In order to investigate possible relationships between the plasticity limits, index, percent passing no.200 and SWCC, 7 type of soils were tested to find its SWCC experimentally and compared the result with the curves obtained from different model presented in the literature. The objectives of the paper were to check the validity of these models with the experimental results. The results shows a good agreement and to present a simple method for inferring the SWCC for soils, taking into account the liquid limit, plastic limit, plasticity index and percent of fines passing sieve no.200.
The present paper addresses the numerical study of non-Darcy laminar forced convectionflows in a pipe partially filled with grooved metallic foam attached in the inner pipe wall,which is subjected to a constant heat flux. Computations are carried out for nine differentdimensions of grooves with different Reynolds numbers namely; (250 ≤ Re ≤ 2000) andtheir influences on the fluid flow and heat transfer are discussed. The governing and energyequations are solved using the finite volume method (FVM) with temperature-dependentwater properties. The novelty of this work is developing of a new design for the metallicfoam, which has not studied previously yet. It is observed that the two helical grooves withtwo pitches increase the Nu around 5.23% and decrease the pumping power nearly 12%. Itis also showed a reduction in the amount of material required for manufacturing the heatexchanger, which leads to a decline in the weight of the system 8.29%.
Previous studies showed that fire incidents cause a considerable deterioration of limestone samples' engineering and physical properties. Various laboratory tests were used in previous studies to investigate the properties of limestone. These tests included destructive and non-destructive tests like the hammer test, ultrasonic pulse velocity test, water-capillary rise test, and water transfer properties test, as well as destructive tests like the unconfined compression test and Brazilian tensile test. The stones of buildings exposed to fire are occasionally assessed on the site. This study analysed the physical and mechanical changes that occurred to the limestone samples when subjected to high temperatures, the damage mechanism, and laboratory or field damage assessment. This study also includes a review of the most significant studies that looked at how alternative cooling techniques—rapid water cooling or gradual air cooling—affect stone samples subjected to high temperatures and compared the behaviour of the samples in each scenario
The present study was concerned with the analysis, simulation of the air flow pat-terns and thermal comfort levels in the University of Anbar at conferences hall (Ibn Al Haitham hall). The study was performed in a hot - dry season. The pur-pose of the present work was to investigate the level of thermal comfort and the influence of the air flow on the flow patterns at the conferences hall. It has been assumed that the total number of occupying audiences in the hall was approxi-mately 100 persons. The present work simulated and analyzed four hypothetical cases, namely: in the first case, the hall was assumed as an empty place, whereas the other three cases were performed by redistribution for the three units of air conditioning, the hall was assumed as a filled place with persons in September 2019. The study was accomplished using simulation techniques, a CFD code (FLUENT 6.2) v.17, which is commercially available. The CFD modelling tech-niques were applied to solve the continuity, momentum and the energy conserva-tion equations in addition to the Turbulence k-є (RNG) model equations for a tur-bulence closure model. Thermal comfort was assessed by finding the values of predicted mean vote (PMV), predicted percentage of dissatisfied (PPD), and ASHRAE standard-55. In conclusion, the second case was the superior in compar-ison to these other cases. It was noted that the PMV value was 0.17, whereas the PPD value was 6.79 at the breathing level.
An experimental study was done on a solar water heater which consists of two prisms of orthogonal triangle cross-section with a 210 liters capacity . The heater was easy to make and has a low cost when comparted with other types of solar water heaters that it usually the collector separate on the water store. The study included experimental investigations , the experimental investigation was done under the Iraqi environmental conditions at Baghdad for the period in summer and winter seasons in 2006 but the calculation for only two days 15/7/2006 and 6/12/2006 . The study included testing the heater with & without loading and it tested in 13/12/2006and14/12/2006. draining hot water from storage tank at different rates . The experimental result show the ability to get hot water at 46oC at December i.e. a temperature rise at 30oC with 16oC initial temperature .
Numerous inserts types are employed in different heat transfer improvement application devices. In this review study is forced on various types of twisted tape inserts in heat exchanger pipe. Geometrical configurations of twisted tape for example twist direction; length, width, space, twist ratio etc. were highly effect on flow pattern, hydrodynamic flow and heat transfer performance. In this review study observed that using different types of twisted tapes can improve thermal performance and hydrodynamic as compared to smooth pipe (without twisted tape). The review investigations found that improvement of thermal performance happens owing to decrease in pipe cross area, leads to rise in mixing flow, turbulence flow intensity flow and rise in swirl flow established through different kinds of twisted tapes. This article dealt with investigations pub-lished in corrugated pipes with varying field applications to provide good information for engi-neers and designers whom dealing and concerning with improvement of heat performance in heat exchanger corrugated pipes.
Numerical solutions are presented for mixed convection from an array of circular cylinders embed in a saturated porous medium. The cylinders are at constant temperature(isothermal) and arranged in a staggered tube bank. Both aiding and opposing flow conditions are considered. Numerical calculations using finite difference method with body-fitted coordinates have covered a wide range of governing parameters(i.e.,10 ،ـ Re ،ـ 100, 0 ،ـ Gr ،ـ 400 and Pr = 0.7). Results are presented for streamline, isotherms and the local and the average Nusselt number at different values of the governing parameters. The present results are compared with previous theoretical results and show good agreement
In this paper, turbulent forced convection of nanofluid flow in channel with isoscelestriangularbaffles is numerically investigated over Reynolds number ranges of 5000-10000.One baffle mounted on the bottom wall of channel and another mounted on the top wall.Al2O3-water nanofluid with nanoparticles volume fraction of 4% and nanoparticles diametersof 25 nm is used. The governing continuity, momentum and energy equations as well as thelow Reynolds number k-ε model of Launder and Sharma have been solved using finitevolume method. The effect of baffle height, baffle distance as well as Reynolds number onthe flow and thermal characteristics have been presented and discussed. It is found that theenhancement ratio of the average Nusselt number as well as the fraction factor increase withincreasing in the baffles height. It is also found that the enhancement ratio of the averageNusselt number increases as the distance of top baffle decrease. Furthermore, the bestthermal-hydraulic performance of channel with triangular baffles using nanofluid can beobtained at baffle height of 2.5 mm, distance of the top baffle of 40 mm and Reynoldsnumber of 5000.
Indeed, there are many hydrology variables influence on the operating of dam and reservoir system. Thus, modelling of dam operation is a complicated issue due to the nonlinearity of such hydrological parameters. Hence, the identification of a modern model with a high capacity to cope with the operation of the dam is extremely important. The current research introduced good an optimization algorithm, namely Genetic Algorithm (GA) to find best operation rules. The main aim of the suggested algorithm is to minimize the difference between irrigation demand and water release value. The developed algorithm was applied to find operation rules for Timah Tasoh Dam, Malaysia. This research used significant evaluation indexes to examine the algorithms' performance. The results indicated that the GA method achieved low Vulnerability, high Resilience and Reliability. It has been demonstrated that the GA method will be a promising tool in dealing with the problem of dam operation.
In this paper, a proposed structure was suggested by replacing the blocks of the fast Haar Wavelet Transform (WT) with a two dimensional wavelet transform at the transmitter and the receiver sides in the Orthogonal Frequency Division Multiplexing (OFDM) model. This can be done by converting a 1-Dimensional vector into a 2-Dimensional matrix and process it by 2-Dimensional Wavelet Transform (2D-WT). The proposed method was applied on the OFDM in Additive White Gaussian Noise (AWGN) and flat fading channel. It was concluded that the proposed method gives much better Bit Error Rate (BER) performance than the conventional OFDM model based on WT. The simulation results showed that the proposd structure outperforms the other scheme in the carried tests at the AWGN and flat fading channels.
In this study, thermal-hydraulic performance of a confined slot jet impingement with Al2O3-water nanofluid has been numerically investigated over Reynolds number ranges of 100-1000. Two triangular ribs are mounted at a heated target wall; one rib located on the right side of the stagnation point and another one located on left side of the stagnation point. The governing momentum, continuity and energy equations in the body-fitted coordinates terms are solved using the finite volume method and determined iteratively based on SIMPLE algorithm. In this study, effects of Reynolds number, rib height and rib location on the thermal and flow characteristics have been displayed and discussed. Numerical results show an increase in the average Nusselt number and pressure drop when Reynolds number and rib height increases. In addition, the pressure drop and average Nusselt number increases with decrease the space between the stagnation point and rib. The maximum enhancement of the average Nusselt number is up to 39 % at Reynolds number of 1000, the rib height of 0.3, rib location of 2 and nanoparticles volume fraction of 4%. The best thermal-hydraulic performance of the impinging jet can be obtained when the rib height of 0.2 and rib location of 2 from the stagnation point with 4% nanoparticles volume fraction.
Solar cells play a vital role in renewable energy systems, and ongoing research is dedicated to enhancing their power efficiency and longevity. Advancements in perovskite solar cells, particularly in power conversion efficiency (PCE), have shown significant progress, confirming its viability as a technology. Perovskite solar cells have achieved power conversion efficiency (PCE) levels of up to 25.5%, comparable to conventional photovoltaic technologies like silicon, gallium arsenide, and cadmium telluride. The substantial enhancement in power conversion efficiency figures over the last decade has shown a remarkable advancement in the efficiency of perovskite solar cells. This study examines the trajectory of perovskite solar cells in becoming economically feasible and generally embraced as a critical renewable energy technology. The advancement of flexible and wearable solar cells, together with miniature solar-powered sensors, has increased the efficiency of solar cell power production. Perovskite solar cells have shown a specific power of 23 W/g, much higher than traditional silicon or gallium arsenide solar cells. Further research is needed to address the challenges related to perovskite solar cells' stability and power conversion efficiency. Perovskite solar cells integrated with energy storage units have the potential to enhance the overall efficiency of the system. This study discusses an approach to improve the efficiency of novel solar cells, specifically focusing on lead-free tin-based perovskite solar cells and tandem solar cells. The advancement of technology in thin films, such as hybrid nanocomposite thin films and quantum dot-sensitive solar cells, has the potential to improve the efficiency of solar cells. The primary outcome of this study is derived from the following inference: incorporating plasmatic nanostructures into thermal energy systems will enhance their efficiency and sustainability by integrating solar energy.
Contemporary researches focused on studying the social effect on architecture from several sides which were distinguished by focusing on the role of mass in forming the architectural personality of that society from the perspective of symbolic side, and moved away from studying this role and its effect on architectural formation from other sides which are more comprehensive and specialized by adding another role that is the individual role from the base of the design influence, and this is what form the foundation and the real need for breakthrough research and quest to understand and view the appropriate comprehensive by studying utilitarian dimension of the relationship between the individual as a designer and the requirements of the group. This research aims to identify the general principles of the relationship of the individual designer group in the light of his understanding of the needs of Variation and their impact in creating a theoretical base for the case of expediency of that relationship and then focus on the study of Instant intellectual emotional bond between the thought of the individual (the designer), the Community and the impact of technology social where the status of the interaction between them and so in order to build a framework My perception is cognitive will be applied to the product of an architect team in order to extract and analyze the results of this application and to explore patterns verify the utilitarian formula of the relationship of the individual (the designer) the group with the introduction of the final conclusions and recommendations.
The concrete members several blessings over steel beam, like high resistance to prominent tem-perature, higher resistance to fatigue and buckling, high resistance to thermal shock, fire re-sistance, robust resistance against, and explosion. However there are some disadvantages as a result of exploitation totally different materials to product it. The most downside of structural concrete member is its deprived the strength to tensile stresses.The bond mechanism between steel bars and concrete is thought to be influenced by multiple parameters, like the strength of the encompassing media, the prevalence of cacophonous cracks within the concrete and therefore the yield stress of the reinforcement. However, properties of concrete mass has significantly effect when it was subjected to elevated temperature.The objective of this paper presents the results that allocating with the bond behavior of the rein-forcement of steel bar systems below static pull-out loading tests subjected to elevated tempera-tures. This numerical technique relies on relative slip and therefore the stress of bond distribu-tions done the embedded length and size of the bar within the concrete cylinder specimens. The obtained results square measure given and commented with the elemental characteristics of ferroconcrete members. The comparison showed smart agreement with experimental results
A numerical investigation of mixed convection from a horizontal cylinder in a saturated porous medium is presented. The governing equations based on Darcy’s law are expressed in a body- fitted coordinate system and solved numerically by explicit method. The direction of the flow varies between the vertically up ward(assisting flow) and vertically downward(opposing flow). Results are presented for Reynolds number Re from 10 to 100 with Grashof numbers up to Gr =5Re. The Prandtl number was kept at a constant value of 0.7. results are presented for the streamlines and isotherms as well as the local and average Nusselt number at different values of governing parameters. Comparison with previous theoretical results show good agreement.
This paper presents an analytical investigation which includes the use of three dimensional nonlinear finite elements to model the performance of the space trusses by using (ANSYS 11.0) computer program. The numerical results show very good agreement (100%) with experimental results, while the graphical option reflects the behavior of the structure under the applied loads because of the ability of this option to simulate the real behavior of the structure under these loads. Also finite element models of the space truss simulate the lateral deflection of the top chord members especially at the corners, and the twisting of the bottom chords.
A numerical study regarding stress, strain, and deflection of a composite plate is presented. The plate, consisting of three layers of Carbon-, Boron-, and Graphite-Epoxy, was fixed at one end and loaded at the other end in a conventional cantilever configuration. Six arrangements were examined and the spatial distribution of stress, strain, and deflection of the upper surface were calculated. Generally, it was found that the order, by which the three layers are arranged, has a great effect on the response of the plate and the maximum stiffness (in terms of deflection) is achieved when using Epoxy with Graphite-Carbon-Boron as the top-central-bottom layers of the plate.
The Artificial Neural Network (ANN) and numerical methods are used widely for modeling andpredict the performance of manufacturing technologies. In this paper, the influence of millingparameters (spindle speed (rpm), feed rate (mm/min) and tool diameter (mm)) on material removalrate were studied based on Taguchi design of experiments method using (L16) orthogonalarray with 3 factor and 4 levels and Neural Network technique with two hidden layers and neurons.The experimental data were tested with analysis of variance and artificial neural networkmodel has been proposed to predict the responses. Analysis of variance result shows that tooldiameters were the most significant factors that effect on material removal rate. The predictedresults show a good agreement between experimental and predicted values with mean squarederror equal to (0.000001), (0.00003025), (0.002601) and (0.006889) respectively, which produceflexibility to the manufacturing industries to select the best setting based on applications.
Since FGM orthotropic structures have such striking qualities as high strength, exceptional stiffness, stiffness-to-weight ratio, reduced cost, and high strength-to-weight ratio, they are employed extensively in the mechanical, aerospace, and civil engineering sectors. Thick plates and shells have more noticeable shear deformation effects. Therefore, in recent years, there has been a lot of interest in the vibration and buckling investigation of FGMs orthotropic plates and shells. Moreover, researchers have developed a variety of approaches and procedures for the examination of orthotropic FGM plates and shells. The majority of the literature review in this publication is focused on orthotropic FGMs plate and shell buckling and linear and nonlinear free vibration. In engineering practices, it is customary to use material-oriented or orthotropic materials in several domains to optimize the structures and maximize material properties, which is especially crucial for FG constructions. Solutions for the orthotropic FGM structure are studied analytically and numerically with different plate and shell theories.
This research represents part of the current attempts to employ remote sensing data in the scopes of the civil engineering and the geotechnical engineering applications. There is great need to know the kinds of soil and their geotechnical properties, to create recent maps which have the capability and high flexibility to deal with them in digitizing way. Therefore GIS techniques are employed in the soil of area of study . By using ArcView software, a geographical database and information about soil chemical properties analysis have been registered and constructed digitally to represent the geotechnical soil characteristics maps . The work includes the digital image processing ( digital classification techniques) by using ERDAS, ver.,8.4 package, and classify the soil of study area by using the supervise and unsupervised techniques . The geotechnical maps by using GIS techniques depend on remote sensing data are the better to represent the ground truth regarding the characteristics of soil , in comparison with the traditional method, because they are easy way to produce, use, store and update, in addition they save in efforts, time and cost . The results of this study have shown that the soil of study area is gypsum where it ratio exceeded the allowable ratio ( 10.75 % ) for all samples . In addition the total Soluble Salts ratio and SO4 ratio high compared to allowable ratio (10 % , 5 %) respectively .
Progressive collapse is a partial or total failure of a building that mostly occurs when the build-ing loses primary structural elements (typically columns) due to accidental or natural hazards. The failure of structures due to an earthquake is one of the most important and frequent types of progressive collapse. In this study, the finite element method is used to assess the response of multistory reinforced concrete buildings subjected to column loss during an earthquake. Three-dimensional nonlinear dynamic analyses are carried out using SAP2000 V.20 program. The ef-fects of different parameters on the progressive collapse behavior are investigated, namely: the location of the removed column within the ground floor; the method of column removal (sudden, in two-steps, and in four-steps) and the removal timing during the earthquake. It is demonstrated that the collapse occurs when all or most of the hinges at the bases of the ground floor columns reach their collapse level. The chosen column removal timing and policy affect the structural behavior considerably. It is realized that, the risk of building collapse increases when the removal timing harmonizes with the peak ground acceleration timing. Based on the adopted earthquake characteristics and building configurations, it is found that, the two steps removal scenario is the most dangerous one.Keywords:Progressive collapse, Concrete buildings, Seismic load, Nonlinear dynamic analysis, Plastic hinge.© 2014
The detection of faults in electronic circuits is crucial to ensure the proper performance and reliability of electronic applications that utilize these devices. This work discovers, for the first time, that a direct tester board for fault diagnosis can be used not only for the intended measurement of current and voltage but also for studying the potential development of these magnitudes in inaccessible locations, as it detects register transfer level signals through oscilloscopes with low acquisition speeds. The experimental analysis carried out combines the use of commercial software with spatial distribution tracking and the exploitation of the sizes of network links in their computer graphical representation. The proper detection of malfunctions in electronic systems is crucial for enhancing their performance and reliability. We intend to explore the troubleshooting of analog electronic systems, for which we use wide-band direct tester boards. To evaluate its performance in routine practice, we perform experimentation using two different analog circuits designed. They consist of conventional operational amplifiers and element modeling based on equivalent resistance-capacitance networks. Given the procedure followed, commercial programs were used. Special mention should be made of the conclusion matrix, which is interesting when selecting suitable diagnostic parameters. The effectiveness of direct measurement based on integrated probes in the two projects, which allowed for fault insertion, was also confirmed. The results and discussions were enriched by the summarized experimental test report. The work concludes with a reflection on the relationship between this work and the existing state of the art, as well as the new challenges posed by international researchers.
An experimental and theoretical study has been conducted to determine the thermal efficiency of a parabolic trough solar collector. The experiments have been performed during winter and summer at Tikrit-Iraq. The solar radiation of Tikrit University was calculated theoretically and a theoretical study was performed by using FORTRAN 90 program. The dimensions and specifications of the collector were entered to the program to determine the theoretical thermal efficiency. It has been found the experimental thermal efficiency of collector is less than the theoretical one in percentage between (7-15) .So the increase in water mass flow rate leads to an increase in the thermal efficiency, and there is no significant change in thermal efficiency when the water mass flow rate becomes more than forty kilograms per hour.
Concrete structures suffer from the impact of many harmful attacking materials that affect theproperties of the main material in them, which is concrete. These structures are also, exposedto the negative impact of many hostile environments such as soils containing harmful salts andharmful acids. A number of precautions should be considered in order to protect the concreteused in such structures. Adding polymer to concrete components as a percentages weight ofcement is one of the methods for producing polymer-modified concrete, which has lowpermeability, better mechanical properties and is more resistant to the negative effects ofharmful environmental factors. The utilization of polymers could help in protecting structuresand enhancing concrete strength. In this study, concrete mixes were prepared with inclusion ofstyrene butadiene rubber (SBR) polymer at four percentages (0%, 5%, 7% and 10% by cementweight). Co-polymers of butidine with styrene (styrene-butadine rubber (SBR)), are a group oflarge-volume synthetic rubbers. High adhesion occurs between the polymer films that formand cement hydrates. This action gives improves the properties of concrete such as flexuraland compressive strength and gives also a higher durability. The investigation was extended toevaluate the compressive strength of the SBR concrete mixes immersed in three types ofwaters: tap, drainage and ground water, at three different ages. The results showed that SBRpolymer enhanced the compressive strength of concrete significantly. A comparison betweenreduction in strength of concretes immersed in these three types of waters was also presented.Moreover, the presence of SBR polymer led to reduced loss in strength of concrete specimensimmersed in drainage and ground water. A proposed model to determine the compressivestrength of concrete specimens immersed in drainage and ground waters was deduced. Thismodel could be a helpful tool for rapid and easy estimation of the strength of concretespecimens immersed in drainage and ground water at different contents of SBR polymer. Theresults showed the highest improve in compressive strength to be associated with 7% SBRmixes at the three tested ages. The increases in this strength at days 7, 28 and 56 with inclusionof 7% SBR polymer were 112.8%, 113.9% and 116%, respectively, compared to OPC mix.
This research presents an experimental and theoretical investigation of the effect of cutouts on the stress and strain of composite laminate plates subjected to static loads. The experimental program covers measurement of the normal strain at the edges of circular and square holes with different number of layers and types of composite materials by using strain gages technique under constant tensile loads. A numerical investigation has been achieved by using the software package (ANSYS), involving static analysis of symmetric square plates with different types of cutouts. The numerical results include the parametric effects of lamination angle, hole dimensions, types of hole and the number of layers of a symmetric square plate. The experimental results show good agreement compared with numerical results. It is found that increasing the number of layers reduces the value of normal strain at the edges of circular and square holes of a symmetric plate and the maximum value of stress occurs at a lamination angle of (30o) and the maximum value of strain occurs at a lamination angle of (50o) for the symmetric square plates subjected to uni-axial applied load. The hole dimensions to width of plates ratio is found to increase the maximum value of stress and strain of a symmetric square plate subjected to uniaxial applied load. Moreover, the value of maximum stress increases with the order of type of circular, square, triangular and hexagonal cutout, whereas the value of maximum strain increases with the order of type of circular, square, hexagonal and triangular cutout.
RSM and DOEs approach were used to optimize parameters for hypoeutectic A356 Alloy. Statistical analysis of variance (ANOVA) was adopted to identify the effects of process parameters on the performance characteristics in the inclined plate casting process of semisolid A356 alloy which are developed using the Response surface methodology (RSM) to explain the influences of two processing parameters (tilting angle and cooling length) on the performance characteristics of the Mean Particle Size (MPS) of α-Al solid phase and to obtain optimal level of the process parameters. The residuals for the particle size were found to be of significant effect on the response and the predicted regression model has extracted all available information from the experimental data. By applying regression analysis, a mathematical predictive model of the particle size was developed as a function of the inclined plate casting process parameters. In this study, the DOEs results indicated that the optimum setting was approx. (44) degree tilt angle and (42) cm cooling length with particle size (30.5) μm
Reverse osmosis (RO) is a membrane filtering system that uses a semipermeable membrane to remove contaminants from water before sending the purified water on to be used in a number of settings, such as households and factories. The goal of this study is to investigate the process of reverse osmosis as well as the current status of the membrane materials that are used in the process. These membrane materials are the driving elements in the process. This review also includes a discussion on the cleaning of membranes, the utilization of RO systems for a number of applications, and new advancements in the field of reverse osmosis. In the process of cleaning water, reverse osmosis, also known as RO, is a potent technique that makes use of a semi-permeable membrane to remove hazardous bacteria as well as dissolved particles. This technique is utilized on a regular basis for the purpose of desalinating seawater for use in drinking, agricultural, and industrial applications.
An experimental study is carried out to compare the thermal performance of a sintered powder metal wick heat pipe. Pure water and absolute ethanol are used as two different working fluids. The pipe is made of copper with 300 mm length, 14 mm diameter, and 1.0 mm wall thickness. The wick is made of copper powder. All the experiments are accomplished and the heat pipe is at the horizontal position (è=0o). The heat flux changed within the range (2.8 -13.13) kW/m2, while all other conditions remained constant. The results show that the thermal performance of the heat pipe is better when water is the working fluid, where the operating temperature and the thermal resistance of the heat pipe are lower when the water is the working fluid.